Difference between revisions of "Electronics notes/Temperature sensing"

From Helpful
Jump to: navigation, search
m (Thermistor)
m (Thermistor)
Line 34: Line 34:
 
'''PTC''': positive temperature coefficient,  
 
'''PTC''': positive temperature coefficient,  
  
The basic resistance varies with intent, though is usually somewhere in the range of 1000 - 2000 Ohm
+
 
 +
The 'at-rest' resistance varies with intent <!--, though is usually somewhere in the range of 1000 - 2000 Ohm-->
  
  
 
They are frequently used in temperature sensing, temperature regulation, and (over)current protection.
 
They are frequently used in temperature sensing, temperature regulation, and (over)current protection.
 +
 +
<!--
 +
Since PTCs are effectively self-regulating,
 +
larger versions are useful as heaters,
 +
and sometimes as mechanical components, such as washing machine locks.
 +
 +
 +
 +
-->
  
  

Revision as of 16:57, 9 June 2019

This is for beginners and very much by a beginner. It's meant to try to cover hobbyist needs, and as a starting point to find out which may be the relevant details for you, not for definitive information.

Some basics and reference: Volts, amps, energy, power · Ground · batteries · resistors · changing voltage · transistors · fuses · diodes · varistors · capacitors · inductors · transformers · baluns · amplifier notes · frequency generation · skin effect


And some more applied stuff:

IO: IO and wired communication · localish communication · wireless (ISM RF, GSM, RFID, more) · 802.11 (WiFi) · 802.15 (including zigbee)


Sensors: General sensor notes, voltage and current sensing · Knobs and dials · Pressure sensing · Temperature sensing · humidity sensing · Light sensing · Movement sensing · Capacitive sensing · Touch screen notes

Actuators: General actuator notes, circuit protection · Motors and servos · Solenoids

Some stuff I've messed with: Avrusb500v2 · GPS · Hilo GPRS · Bluetooth serial · JY-MCU · DMX · ESC/POS notes

Audio notes: basic audio hacks · microphones · amps and speakers · device voltage and impedance, audio and otherwise ·

Less sorted: Common terms, useful basics, soldering · Microcontroller and computer platforms · Arduino and AVR notes · ESP series notes · Electronics notes/Phase Locked Loop notes · mounts, chip carriers, packages, connectors · signal reflection · pulse modulation · electricity and humans · Unsorted stuff


See also Category:Electronics.

This article/section is a stub — probably a pile of half-sorted notes, is not well-checked so may have incorrect bits. (Feel free to ignore, fix, or tell me)

Thermocouple

Inexpensive High range of temperature Not highly accurate - assume you won't get better than 1 degree Celcius of resolution, less if you don't calibrate well


Age with time and high-temperature use, so will need occasional recalibration and/or replacement.


They produce voltage due to the thermoelectric effect - on the order of millivolts so most uses, and accurate use, requires amplification (with high input impedance to avoid the measurement affecting the thermocouple itself).


https://en.wikipedia.org/wiki/Thermocouple#Types

Thermistor

Most resistors vary their resistance with temperature. A thermistor (thermal resistor) does it intentionally, and more pronounced.


NTC: negative temperature coefficient, resistance drops (logarithmically) as its body temperature increases

PTC: positive temperature coefficient,


The 'at-rest' resistance varies with intent


They are frequently used in temperature sensing, temperature regulation, and (over)current protection.


Perhaps the he simplest way to get a voltage from a thermistor (think ADC, comparator) is to have it be one leg of a voltage divider.



Power thermistor

A power thermistor is a very low-resistance (NTC) thermistor in series with your main current, as a current limiter and/or (self-resetting) overcurrent protector.

One use is to lessen the sudden inrush current in transformers and such:

  • place in series with the primarily coild
  • when cold (just switched on) it typically has a few hundred ohm resistance
  • and once it warms it (few seconds later) goes to under an ohm.

This lessens the magnitude of the sudden current that can happen right after you switch something on.


See also:

Diodes

The voltage across a diode will decrease by ~2 mV per °C in a fairly linear way.

You need amplification and probably a DAC, accuracy isn't great, but it's very convenient inside FPGAs, processors, and such.

Unsorted

See also

http://www.electronics-tutorials.ws/io/io_3.html