Electronics notes/frequency generation

From Helpful
Revision as of 16:16, 26 March 2012 by Helpful (Talk | contribs)

Jump to: navigation, search
This is for beginners and very much by a beginner.

It's intended to get an intuitive overview for hobbyist needs. It may get you started, but to be able to do anything remotely clever, follow a proper course.

Some basics and reference: Volts, amps, energy, power · Ground · batteries · resistors · changing voltage · transistors · fuses · diodes · varistors · capacitors · inductors · transformers · baluns · amplifier notes · frequency generation · skin effect

And some more applied stuff:

IO: Input and output pins · wired local IO wired local-ish IO · · · · Shorter-range wireless (IR, ISM RF, RFID) · bluetooth · 802.15 (including zigbee) · 802.11 (WiFi) · cell phone

Sensors: General sensor notes, voltage and current sensing · Knobs and dials · Pressure sensing · Temperature sensing · humidity sensing · Light sensing · Movement sensing · Capacitive sensing · Touch screen notes

Actuators: General actuator notes, circuit protection · Motors and servos · Solenoids

Some stuff I've messed with: Avrusb500v2 · GPS · Hilo GPRS · JY-MCU · DMX · Thermal printer

Audio notes: basic audio hacks · microphones · amps and speakers · device voltage and impedance, audio and otherwise ·

Less sorted: Common terms, useful basics, soldering · Microcontroller and computer platforms · Arduino and AVR notes · ESP series notes · Electronics notes/Phase Locked Loop notes · mounts, chip carriers, packages, connectors · signal reflection · pulse modulation · electricity and humans · Unsorted stuff

See also Category:Electronics.

This article/section is a stub — probably a pile of half-sorted notes, is not well-checked so may have incorrect bits. (Feel free to ignore, fix, or tell me)

Oscillators, resonators, crystals, and such.

Simpler things that go tick can be anything that intentionally resonates - ceramic resonators, flip-flop constructions, a 555, or whatnot.

Timekeeping is often based on crystals, because they are more regular and the accuracy more predictable.

Applications include:

  • clock source (for digital elements, digital communication)
  • reference clock
  • signal generator

In basic electronics you see a bunch of ceramic resonators (cheap, can be used when the rate is more imporant that it is for the interval to be strictly regular), and simpler quartz crystal oscillators (more accuracy than resonators), and corrected quartz crystal oscillators (more accuracy than basic quartz; necessary for some applications).

Frequency tolerance refers to how close the real frequency will be to the spec.

This is about production quality, about what a specific crystal ends up doing exactly, and also about some specific effects, such as that of temperature on quartz. Any given crystal is likely to be relatively consistent. A crystal that is ±50ppm will probably not be +30 one day and -40 the next. This means that you can calibrate away the 'average' error once you measure it, though you are still left with other errors.

Frequency tolerance of ±250ppm or more is considered relatively relaxed, ±20 ppm is pretty good, lower than that is fairly strict.

You can spend ten bucks on a TCXO that is 2ppm (approx. 1 second per ~5 days, approx. 1 minute per year). For regularity this is good stuff.

...but for accurate timekeeping it's still only so-so, and there are other ways of receiving good time. One of them is GPS (which requires accurate time to even work), and most of the western world has radio-wave synchronization (which is the cheaper option unless you had GPS anyway).

Digital watches typically have quartz crystals with few-dozen ppm accuracy. And yes, that means they're often off by a few minutes per year. Fancy digital watches are typically radio synchronized - it's easier and cheaper than getting something to be that much more regular.

Loose frequency generation:

  • harmonic/linear, oscillator (waveform like a sine wave) [1]
  • relaxation oscillator (waveform like a sawtooth) [2]

  • Low-Frequency Oscillator (LFO) - designs that generates a waveform below ~20 Hz. Used in synthesizers and such.
  • Surface acoustic wave (SAW) oscillators - quartz crystals that achieve higher frequencies though a standing-wave construction. More expensive, but necessary for devices that
    • frequency tolerance: on the order of 0.0001


  • ceramic resonators are less accurate than crystals, but good enough whenever timing need not be that accurate
    • frequency tolerance: on the order of 0.5% (5000ppm) (7.2min/day)
  • crystal oscillators - piezoelectric quartz.
    • frequency tolerance: on the order order of ~0.001% (~10ppm) (~0.86sec per day),
    • Tunable within a small range of frequencies
    • Fairly cheap
    • not accurate enough for certain some applications (such as some radio transmission, long-term timekeeping, stability under varying temperatures)

  • TCXO (temperature-compensated crystal oscillator)
    • less than 5 PPM, usually 2 or 3(verify), down to 0.1 PPM is theoretically possible. A little more complex than basic crystals, and still fairly affordable

  • MCXO (microcontroller-compensated crystal oscillator)
    • refers to designs that are more stable and avoid more noise and drift (useful when supporting less predictable things like uCs) (verify)
    • Down to 0.1PPM

See also: