Electronics project notes/Audio notes - Digital sound communication
This is mostly about hardware interconnects. For software media routing, see Local and network media routing notes
Typically external
AES3 and S/PDIF
Serial, one-directional, digital audio data.
AES3 is a digital audio protocol from 1985(verify) seemingly apparently aimed at communicating 44.1 kHz, 48 kHz, and also 32kHz (e.g. from existing formats like CD audio, DAT, and some other things, and potentially from digital-only devices).
It was co-developed by AES and EBU, and at the time was often marked 'AES/EBU' on devices. You can treat AES/EBU as meaning AES3.
S/PDIF ("Sony/Philips Digital Interface")
is based on AES3, can be seen as a consumer variant of AES3, simplifying the way it would be implemented and appear to consumers(verify)
From a practical standpoint, you now mostly care about S/PDIF, until you work with some older devices.
But also, a lot of streams will be valid to both(verify)
IEC 60958 (a.k.a. IEC958 before IEC's renumbering in 1998)
seems to have absorbed both, which makes historical distinctions and incompatibilities
a little more interesting to figure out for newcomers.
This also confuses the connector part. Say, IEC60958 now defines:
- Over XLR3 (IEC 60958 Type I), balanced
- Over RCA (IEC 60958 Type II), unbalanced
- Over TOSLINK (IEC 60958 Type III)
- Over BNC, unbalanced, was used in broadcasting (probably in part because it could be used over existing BNC/Coax)
Notes:
- Broadly speaking
- XLR3 and BNC are likely to be AES3 pedigree
- TOSLINK and BNC are likely to be S/PDIF flavour.
- (though there was a time at which it could also be AES3.(verify))
- Even though XLR is balanced, it was still only meant for shorter distances; BNC was intended for somewhat longer runs (verify)
- Expansions of the standard also added additional formats, that earlier hardware would not know
- Raw PCM is the basic form, but S/PDIF devices may also understand
- DTS for 5.1/7.1 -- more specifically the DTS Coherent Acoustics (DCA) codec
- AC3 (Dolby Surround)
- will be loosely corrected with connector, in part just because newer devices use TOSLINK, not XLR/BNC
Compatibility notes:
- Even if the plugs/covnerters allow it, it is not recommended to plug AES3 directly into S/PDIF without further thought.
- Conversion at electrical level is not necessarily hard, and some devices are engineered to accept both, but don't count on it
See also:
Not to be confused with
- AES/EBU (next section)
ADAT
ADAT has referred to two distinct things
Historically, and now rarely, to the Alesis Digital Audio Tape, a way of storing eight digital audio tracks onto Super VHS.
These days, so much more typically, it refers to the ADAT Optical Interface, more commonly known as ADAT Lightpipe or often just ADAT (or lightpipe), also from Alesis.
It looks the same as TOSLINK / S/PDIF, but speaks a different protocol, and somewhat faster.
It carries audio channels that are always 24 bit (devices that are 16-bit will effectively just use the 16 highest bits).
Its speed lets it carry
- up to eight channels of those at 48kHz.
...or, with the common S/MUX extension
- up to four channels at 96kHz
- up to two channels at 192kHz
See also:
Typically internal
I2S
(Note: no technical relation to I2C)
(has existed since the mid-eighties)
I2S (sometmimes IIS), Inter-IC Sound, is meant as an easy and standard way to transfer PCM data between closeby chips.
It separates clock and data, so it can have slightly lower jitter (and indirectly latency) than buses that don't.
As I2S doesn't spec a plug, or how to deal with longer cables (impedance and such), it is mostly used within devices.
Exceptions mainly being audiophile setups that want to choose their DACs separately. Because it wasn't made for that, this takes more care to do right, because impedance can cause synchronization issues, particularly at higher bitrates.
Lines and bits and interpretation
The lines are
- bit clock (BCLK) (a.k.a. continuous serial clock (SCK))
- left-right clock (LRCLK) (a.k.a. word clock, word select (WS), Frame sync (FS))
- data
- ground
BCLK pulses for each bit, so should be samplerate * bitdepth * channelamount, e.g. 1411200 Hz for CD audio (44100*16*2).
LRCLK selects left/right channel
Some also add a master clock (MCLK). This is not part of standard I2S
Note that:
- The protocol is fundamentally 2-channel (in part due to LRCLK's function)
- If you functionally want to send mono, you could send zero on the other.
- but if you have that sample anyway, then it makes just as much sense to output it twice, i.e. in both channels, so that if a receiver decides to implement mono by picking one channel, it doesn't matter which one. And stereo playback will be double mono rather than seeming to miss one channel.
- Sample rate is not configured, it is implicit from the sending speed(verify),
- which is part of why software bit-banging I2S would probably never sound great
- Bit depth is implied by when LRCLK switches (which it can do because the MSB goes first)
- with some work left to the receiver
DIY abuse
Because I2S interfaces are fairly high-speed, and typically DMA-assisted, it has found other uses.
Because channels=2, sample rate is controlled by the clock, and bit depth is somewhat implied,
you can vary some aspects of what it sends without negotiating it.
For example, when feeding in data into an I2S DAC, you do need to do the stereo interlacing as in the spec, and the bit depth as the DAC expects, but it doesn't need know the sample rate - it will do what you ask of it, at the rate you ask it to.
For example, the ESP8266 and ESP32's I2S is actually run from a more generic piece of hardware, roughly a glorified shift register, used to implement I2S as well as LCD and camera peripherals.
It happens to go at ~1.4MHz for audio, probably from a configured, but if you can control the output rate, then you can produce other sorts of signals, and DIYers have found it's fairly stable at 40MHz, which makes it possible to produce NTSC and VGA signals, and could even sample data at that rate.
Similarly, RP2040 has a Programmable I/O (PIO)[1] [2] [3]
You could probably send PDM over these - which would be an ironic use of something already intended for audio, but which might makes sense if the receiving side isn't an I2S DAC(verify).
See also:
- https://web.archive.org/web/20140223115501/http://www.eng.auburn.edu/~nelson/courses/elec5260_6260/Inter-IC%20Sound%20%28I2S%29%20Bus2.pdf
- https://web.archive.org/web/20080706121949/http://www.nxp.com/acrobat_download/various/I2SBUS.pdf